移植linux2.6.29内核及根文件系统到UP-CPU-2410（2）

二、移植linux内核
所需文件：
内核：Linux-2.6.29.1.tar.bz2
yaffs2代码：cvs-root.tar.gz
解压在工作目录下,分别是：
linux-2.6.29.1
cvs

1.修改内核源码
修改内核根目录的makefile，第193行：
ARCH ?=arm
CROSS_COMPILE ?=arm-linux-

修改MTD分区：
$vim arch/arm/plat-s3c24xx/common-smdk.c

static struct mtd_partition smdk_default_nand_part[] = {
[0] = {
.name = "vivi",
.size = 0x00020000,
.offset = 0,
},
[1] = {
.name = "param",
.offset = 0x00020000,
.size = 0x00010000,
},
[2] = {
.name = "kernel-2.6.29",
.offset = 0x00030000,
.size = 0x00200000,
},
[3] = {
.name = "root",
.offset = 0x00230000,
.size = 0x00800000,
},
[4] = {
.name = "yaffs",
.offset = 0x00a30000,
.size = 0x035cc000,
}
}

修改ECC校验：
$vim driver/mtd/nand/s3c2410.c
找到s3c2410_nand_init_chip()函数，将其中的
chip->ecc.mode=NAND_ECC_SOFT;
改成
chip->ecc.mode=NAND_ECC_NONE;

2.为内核打yaffs文件系统补丁
$cd cvs/yaffs2
$./patch-ker.sh c ../../linux-2.6.29.1/

3.移植DM9000网卡驱动
访问基址是0x10000000（BANK2）：Index地址是0x10000000，Data地址是0x10000002.
地址线是ADD1,链接DM9000的CMD引脚，
总线位宽16位，
中断引脚为EINT2

添加DM9000平台设备：
$vim arch/arm/plat-s3c24xx/common-smdk.c
/*添加要包含的头文件*/
#if defined(CONFIG_DM9000)||defined(CONFIG_DM9000_MODULE)
#include <linux/dm9000.h>
#endif
/*添加DM9000的平台设备结构*/
#if defined(CONFIG_DM9000)|| defined(CONFIG_DM9000_MODULE)
static struct resource s3c_dm9k_resource[] = {
[0] = {
.start = S3C2410_CS2, //ADD1=0时使用的地址
.end = S3C2410_CS2 + 1,
.flags = IORESOURCE_MEM,
},

[1] = {
.start = S3C2410_CS2 + 2, //ADD1=1时使用的地址
.end = S3C2410_CS2 + 2 + 1,
.flags = IORESOURCE_MEM,
},
[2] = {
.start = IRQ_EINT2, //中断号
.end = IRQ_EINT2,
.flags = IORESOURCE_IRQ,
}
};

static struct dm9000_plat_data s3c_dm9k_platdata = {
.flags = DM9000_PLATF_16BITONLY, //数据总线宽度为16位
};

static struct platform_device s3c_device_dm9k = {
.name = "dm9000",
.id = 0,
.num_resources = ARRAY_SIZE(s3c_dm9k_resource),
.resource = s3c_dm9k_resource,
.dev = {
.platform_data = &s3c_dm9k_platdata,
}
};
#endif

/*加入内核设备列表*/
static struct platform_device __initdata *smdk_devs[] = {
/*DM9000*/
#if defined(CONFIG_DM9000) || efined(CONFIG_DM9000_MODULE)
&s3c_device_dm9k,
#endif
...
...
};

修改DM9000驱动程序:
$vim drivers/net/dm9000.c
/*添加要包含的头文件*/
#if defined (CONFIG_ARCH_S3C2410)
#include <mach/regs-mem.h>
#endif

/*设置存储控制器使BANK2可用，设置默认MAC地址*/
/*添加的代码被宏CONFIG_ARCH_S3C2410包含起来*/
dm9000_probe(struct platform_device *pdev)
{
......
int i;
u32 id_val;
/*DM9000 device*/
#if defined(CONFIG_ARCH_S3C2410)
unsigned int oldval_bwscon;
unsigned int oldval_bankcon2;
#endif

......

SET_NETDEV_DEV(ndev, &pdev->dev);
dev_dbg(&pdev->dev, "dm9000_probe()/n");

/*DM9000 device*/
#if defined(CONFIG_ARCH_S3C2410)
oldval_bwscon = *((volatile unsigned int *)S3C2410_BWSCON);
*((volatile unsigned int *)S3C2410_BWSCON) = (oldval_bwscon & ~(3<<8)) | S3C2410_BWSCON_DW2_16 | S3C2410_BWSCON_WS2 | S3C2410_BWSCON_ST2;

oldval_bankcon2 = *((volatile unsigned int *)S3C2410_BANKCON2);
*((volatile unsigned int *)S3C2410_BANKCON2) = 0x1f7c;
#endif
......

if (!is_valid_ether_addr(ndev->dev_addr)) {
dev_warn(db->dev, "%s: Invalid ethernet MAC address. Please "
"set using ifconfig/n", ndev->name);

/*DM9000 device*/
#if defined(CONFIG_ARCH_S3C2410)
printk("NOW use the default MAC address: 08:90:90:90:90:90/n");
ndev->dev_addr[0] = 0x08;
ndev->dev_addr[1] = 0x90;
ndev->dev_addr[2] = 0x90;
ndev->dev_addr[3] = 0x90;
ndev->dev_addr[4] = 0x90;
ndev->dev_addr[5] = 0x90;
#endif
}
......

out:
dev_err(db->dev, "not found (%d)./n", ret);

#if defined(cONFIG_ARCH_S3C2410)
*((volatile unsigned int *)S3C2410_BWSCON) = oldval_bwscon;
*((volatile unsigned int *)S3C2410_BANKCON2) = oldval_bankcon2;
#endif
......
}

/*注册中断，指定触发方式*/
dm9000_open(struct net_device *dev)
{
......
irqflags |= IRQF_SHARED;

#if defined(CONFIG_ARCH_S3C2410)
if (request_irq(dev->irq, &dm9000_interrupt, IRQF_SHARED|IRQF_TRIGGER_RISING, dev->name, dev))
#else
if (request_irq(dev->irq, &dm9000_interrupt, IRQF_SHARED, dev->name, dev))
#endif
return -EAGAIN;
......
}

4.配置内核
$make s3c2410_defconfig
$make menuconfig
[*] Enable loadable module support --->
[*] Forced module loading
[*] Module unloading

System Type --->
S3C2410 Machines --->
[*] SMDK2410/A9M2410
其余Machines都不选（包括2400,2440等）

Kernel Features --->
[*] Use the ARM EABI to compile the kernel
Boot options --->
noinitrd root=/dev/mtdblock3 init=/linuxrc console=ttySAC0

Userspace binary formats --->
[*] Kernel support for ELF binaries

Device Drivers --->
[*] Network device support --->
[*] Ethernet (10 or 100Mbit) --->
<*> DM9000 support

File systems --->
[*] Miscellaneous filesystems --->
<*> YAFFS2 file system support
[*] Lets Yaffs do its own ECC
-*- Native language support --->
<*>Codepage 437 (United States, Canada)
<*>Simplified Chinese charset (CP936, GB2312)
<*>Traditional Chinese charset (Big5)
<*>ASCII (United States)
<*>NLS ISO 8859-1 (Latin 1; Western European Languages)
<*>NLS UTF-8

$make zImage

将/arch/arm/boot目录下生成的zImage下载到kernel分区。